NetBSD/macppc Old Frequently Asked Questions
NetBSD/macppc Old Frequently Asked Questions
Introduction
General Information
- USB keyboard problems
- panic: startup: cannot allocate VM for buffers
- wdc0:0:1: lost interrupt
- pciide0:0:0: lost interrupt
- Panic: mesh: FIFO != 0
- I'm getting device timeouts on bm0
- What's the deal with the "load-base" setting?
- PowerBook (FireWire), PowerBook G4 (Titanium), and BootROM 4.1.8
- Woah, my machine just powered off!
- Where's my disk? (a.k.a. sysinst says I can not find any hard disk for use by NetBSD)
Other sources of information
Introduction
About this FAQ
This frequently asked questions (and answers) document covers problems with NetBSD/macppc prior to the 1.6 release.
If you have encounter a problem listed here as being fixed,
have additional information, questions, or answers, send mail to
<port-macppc@NetBSD.org>
General Information
USB keyboard problems
There are two different types of USB keyboard problems. One set of problems appeared after NetBSD 1.4.3 was released, and applies only to some iMac (Bondi Blue) and some PowerMacintosh G3 (Blue and White) machines. This problem seems to have been fixed in NetBSD 1.6.
The other problem occurred on all models with USB keyboards, but was fixed prior to the release of NetBSD 1.5.
See Bob Nestor's post to the mailing list describing the problem and a workaround for the PowerMacintosh G3 (Blue and White). This workaround doesn't work for the iMac (Bondi Blue), but Rob Gridley reports that unplugging the mouse allows his system to boot and use the keyboard. Also, see the problem report, port-macppc/12894
Briefly, what he recommends is:
Unplug the USB keyboard and plug in an ADB keyboard and mouse
Boot NetBSD with the ADB keyboard
Enter root, swap and filesystem responses on the ADB keyboard
When the system gets to the shell prompt (or login if you went multi-user), unplug the ADB and plug in the USB keyboard
The USB will be usable at this point and you can use the system. You'll notice that the ADB is dead even before you unplugged it. Also you MUST boot without the USB installed or this won't work.
Alternatively, NetBSD 1.4.3 works fine on these two models and does not have this USB keyboard problem.
There is a problem in some kernels that causes the first keypress
from a USB keyboard to be repeated over and over again. A symptom
of this would be the install system continually asking (I)nstall,
(S)hell or (H)alt ?
To avoid this problem, press the
shift key before anything else.
On some newer machines, NetBSD will hang after configuring the devices but before entering single-user mode. The recommended solution is to unplug all USB devices (especially hubs) and plug the mouse into the keyboard and the keyboard directly into the back of the mac.
panic: startup: cannot allocate VM for buffers
This problem should have been fixed in NetBSD 1.5.
On some machines with large quantities of RAM the kernel will run out of kernel VM when it tries to allocate the buffer cache. You can avoid this by either of:
Removing some RAM
Adding
options BUFPAGES=800
to the kernel configuration
wdc0:0:1: lost interrupt
This problem is present in NetBSD 1.5.2 on newer machines that support
ATA4 drives. Unfortunately, there is presently no easy workaround. Post
to <port-macppc@NetBSD.org>
for assistance.
This has been reported on the iBook (Dual USB) and the iMac (Summer 2000) which has been updated to BootROM 4.1.9.
The problem is not present in NetBSD 1.5.3 and later.
pciide0:0:0: lost interrupt
This problem is fixed in NetBSD 1.5.1 and later.
The NetBSD initialization code for the CMD 646 IDE controller doesn't correctly undo some of the settings that Open Firmware sets. What happens is that Open Firmware sets the IDE controller up in 0646U2 mode and changes some of the interrupt settings. The MI pciide driver doesn't know how to deal with this situation and you get a lot of “lost interrupt” messages.
What this means is that if you use Open Firmware to load the bootloader (i.e. ofwboot.xcf) or the kernel from your hard drive, NetBSD cannot use that drive.
A workaround is to place the kernel on another bootable bus and then use that to mount the drive with your NetBSD filesystem on the drive connected to the CMD 646 IDE bus. The key phrase here is “another bootable bus”. On the G3 and G4 machines which have this problem, they have more than one IDE bus (in addition to add-on SCSI busses). The hard drive is typically on the bus which we have troubles with, but the CD-ROM and Zip drive are typically on a different IDE bus which works just fine.
What you may want to do is move your hard drive to the bus the CD-ROM is attached to (paying attention to the master/slave jumpers), and all your problems will go away, although your drive is using a slower IDE bus protocol.
Panic: mesh: FIFO != 0
This bug is not present in NetBSD 1.5 and later.
This is usually caused by bad SCSI cabling or devices. Check your internal and external termination. Check the length and quality of your cables. Disconnect all devices that are not critical.
More often than not, this is caused by having a Zip drive on your MESH SCSI bus, as these devices do not behave like good SCSI citizens.
One person suggested that the MESH driver is more reliable if you don't reboot from Mac OS into NetBSD. (That is, if you're running Mac OS, shut down rather than rebooting, and then power it back on and boot to NetBSD.)
M L Riechers posted a very thorough message on this topic.
Good luck.
I'm getting device timeouts on bm0
This problem has been fixed in NetBSD 1.5 and later.
Inserting a 10Mb Hub (forcing bm0 to 10Mb/s instead of 100Mb/s) seems to prevent this problem.
What's the deal with the "load-base" setting?
The Open Firmware environment variable load-base
is the address
at which Open Firmware loads the bootloader from your boot-device
.
The behavior is different for the various versions of Open Firmware and
boot-device
s. The symptom of an incorrectly set load-base
is CLAIM
failed
.
Do not change the load-base
.
Open Firmware 3 machines have re-writable firmware, and users have found
that changing the load-base
has overwritten their flash BootROM,
rendering their machines dead (requiring an expensive trip back to
Apple). Do not change the load-base
on an Open Firmware 3
machine. Apple has fixed Open Firmware 3 such that you needn't change
load-base
to boot.
The default value of load-base
on these
systems is 4000, which isn't very good for our purposes. System Disk sets
load-base
to 600000, which suits us just fine for
NetBSD 1.5.3 and later. mkLinux uses a different value, which may
prevent you from booting NetBSD/macppc. If you're using NetBSD 1.5.3
or later, reading further may simply confuse you -- stop here and just
use 600000.
The load-base
is handled differently by
ofwboot.xcf
and ofwboot
. ofwboot.xcf
is the
XCOFF bootloader used on MS-DOS floppies, ISO CD-Rs, and with netbooting.
ofwboot
is the "partition zero" bootloader on the install floppies,
install CD-R images, and hard drives prepared with sysinst or
installboot.
ofwboot
has been set to use 600000. Therefore,
you should use a load-base
of 600000.
The NetBSD 1.5.3 and later versions of ofwboot.xcf
have been
set to use 640000. Due to a perculiarity of Apple's Open FIrmware,
load-base
must be an address different from the address
ofwboot.xcf
is set to use. Therefore, you should use a
load-base
of 600000. This value is also the correct one for
booting Mac OS X.
The ofwboot.xcf
from NetBSD versions prior to 1.5.3 had been
set to use 600000. Therefore, if you're trying to boot using this bootloader,
you should use a load-base
of 640000
or get a newer version of ofwboot.xcf
Once you are entirely positive that your machine has Open Firmware
1.0.5, 1.1.22, 2.0.x, or 2.4 (see Which version of
Open Firmware does my machine have?), run the following commands to
set your load-base
properly
0 > setenv load-base 600000 0 > reset-all
You should double-check that this value has been set using the
printenv
command.
PowerBook (FireWire), PowerBook G4 (Titanium), and BootROM 4.1.8
The two models listed above will fail to boot NetBSD 1.5.x and earlier if they have have BootROM version 4.1.8 or later.
This problem is fixed in NetBSD 1.6 and later.
Woah, my machine just powered off!
Well, that's probably because you're using a recent laptop (iBook, PowerBook (FireWire), and some later models) and NetBSD 1.5 or later.
The page up key sequence (FN-uparrow
) will panic a NetBSD 1.5.1 or
1.5 kernel. This is fixed in NetBSD 1.5.2 and later.
The “brightness” keys (F1 and F2) will power off your machine and zap your
clock. You will need to build a new kernel without the abtn
option.
Remove the following line from your
kernel configuration:
#abtn* at adb?
Where's my disk? (a.k.a. sysinst says I can not find any hard disk for use by NetBSD
)
Well, that's a good question!
The root cause is that NetBSD didn't find your hard drive (or, more insidiously, didn't find your drive controller). There a variety of reasons why this happens.
If you have a recent machine which support ATA4, and/or you've
installed a recent FirmWare update (late 2001), and you're trying to use
NetBSD 1.5.2, you may run into the
wdc0:0:1: lost interrupt
problem.
The NetBSD 1.5.1 install kernel image does not support the IDE controller in the PowerMacintosh G3 (Blue and White). The real kernel does support it.
Other sources of information
General Information
-
NetBSD/macppc nvedit HOW-TO, for info on how to edit the contents of the NVRAMRC
-
wscons documentation, for NetBSD's platform-independent workstation console driver
Additional information
-
port-macppc mail list - if you have any additional questions please subscribe.
General NetBSD Documentation - for questions not specific to NetBSD/macppc.
Back to �NetBSD/macppc ports page